Photo to Stencil

18 November 2026

How to print a tattoo stencil.

Most failed stencils are a settings problem, not a printer problem. The wrong scale, a double mirror or the wrong paper. Here is what each kind of printer needs, and the two checks that catch almost every mistake.

Three machines print a stencil

A thermal stencil printer prints a file from a phone or computer straight onto thermal stencil paper. A thermal copier copies a paper original onto the same paper with heat. An inkjet printer can print a stencil only as part of a dedicated stencil ink system, with that system's ink and paper.

A normal printer with normal ink does not make a stencil. It makes a plain paper print, which is useful as a size and placement guide or as the original for a copier, but it will not transfer to skin.

With a thermal stencil printer

Use four layer thermal stencil paper: a white top sheet, a thin tissue, the purple carbon and a yellow backing. Tear out the tissue first, or the line lands on the tissue instead of the white sheet. Whether the yellow backing stays on depends on the printer, so follow its manual: Phomemo says to remove it, other guides keep it.

Feed the sheet white side up, print in black only with the darkness or contrast set high, and print at 100%. The line forms on the underside of the white sheet, which is the side that goes on skin.

With a thermal copier

Print the design on plain paper first, ideally on a laser printer: copiers read toner and pencil well, and an inkjet print can copy weak. Then run the original through with a thermal sheet, following the copier's own steps. Use the copier's mirror setting or your file's, never both.

With an inkjet stencil ink system

These systems fill a new tank printer, usually an Epson EcoTank, with stencil ink and print on their own thin stencil paper. The vendors are clear on three points: use their ink and paper together, use a printer that has never had normal ink in it, and expect that printer to stay a stencil printer. Regular printer ink is not made for skin.

Set the scale to 100% and the quality to the highest setting, and mirror anything that is not symmetrical.

The 100% rule

Print at 100%, or Actual size. Turn Fit to page off: it rescales the sheet, and every line moves by the same ratio. Then measure. A ruler on one known width tells you more than any preview. A stencil that is 2 cm off is a tattoo that is 2 cm off.

Mirror once

A stencil goes on skin face down, so the design flips when it transfers. Most thermal printer and inkjet stencil guides say to mirror the design before printing. Do it in one place only: in your file, in the printer's app, or on the copier. Two mirrors cancel out.

Test with one letter. Print a small R through exactly the same settings. On the finished stencil, the R on the purple side should read backwards. If it reads normally, the tattoo would come out reversed.

Which printer

Common thermal stencil printers differ mostly in width and resolution. The Brother PocketJet S8 prints a full page at 300 dpi. The Phomemo M08F and the HPRT MT660 print a full sheet at 203 dpi. The roll fed Phomemo TA81 prints a variable length, which suits a long arm or leg piece. Some portable models take only the maker's own paper, which sets your cost per stencil, so check before you buy. We have not tested these machines; the specs are the makers' own.

At 203 dpi, very fine line work and dot work can fill in. Keep the line weight up or use fewer interior lines for a small piece.

Where the file comes from

Every route above needs a clean line drawing at the right size. Photo to Stencil traces a reference photo into one in your browser. Load the photo, pick a pass, set Print width in centimetres (leave it blank to fit A4 or Letter), and turn on Flip for transfer if your printer route needs the mirror in the file. Then print, or save the sheet as a PNG for your printer's app. Nothing is uploaded.

What it will not do

It does not drive your printer or pick its settings, and it does not fix a sheet that was printed at the wrong scale. It traces the photo you give it, and every line comes from that photo.

The price

Previews are free, and your first 3 full-size sheets are free. After that it is one payment (from $9.99 at launch until 16 December, then $49.99), with no subscription and no credits.

Abrir o criador de estêncil